YARDPUMP · Technical Article

A New Lip Seal Leaks Immediately. Was the Lip Cut by the Keyway?

Inspect the lip for cuts from keyways or shaft edges. Verify the protective sleeve and installation route before attributing an immediate leak to wear.

If a replacement lip seal leaks the first time it sees water, retrace how it was fitted. The running surface is smooth and the spring faces the documented direction. Check the route the lip took to reach its running position. It may have crossed a keyway, splines, a retaining groove or threads. A single sharp edge can cut the working lip before the shaft ever turns. A smooth track cannot compensate for that cut.

Look along the assembly route

A narrow band of the lip contacts the shaft. A small local cut can provide a path for leakage under rotation and pressure. A linear cut on one part of a returned lip, with a corresponding edge along the assembly path, warrants an installation investigation. A wear groove from operation usually follows the shaft contact band around the circumference. Both can occur. A photograph of a cut does not by itself allocate responsibility. Record relative orientation and preserve the as-found condition before cleaning or dismantling.

Read the drawing in assembly order. Which end does the seal enter from? Is the key fitted already? Which shaft steps does the lip cross, and where does the tool push the seal into its bore? Even with no key installed, the slot edges can score the lip. A tool that tilts the seal may push one side over a step first. Define the path in the process instructions instead of depending on the operator to work around every edge by hand. Check service assembly as well as the original factory sequence.

Use a designed installation sleeve

A protective sleeve covers the edges the lip must cross and presents a smooth lead-in and release. Its dimensions and finish should come from the equipment or seal designer. Improvised wrapping can leave an overlap, residue or unintended stretch. If the design permits, assembly from the opposite end or fitting the key later can avoid the problem, but verify whether that route is also available to the repairer. Use only the specified lubricant and installation method. An unknown lubricant can change elastomer behaviour or obscure the examination.

For illustration, suppose the running diameter is 12 millimetres and an improvised sleeve is 13 millimetres outside. Crossing it adds one millimetre of diametral stretch and about 3.1 millimetres of circumference compared with the running surface. That geometry is a reminder to check the tool, not a permitted stretch limit. Ask the manufacturer for the actual sleeve, lead-in and lip handling requirements. A single apparently successful fit is not qualification.

Verify a sample before repeating a repair

On a de-energized fixture, inspect a service sample before mounting, after passing the protected edge and at installed depth. Check for tilt and where the contact band sits, then follow the approved static and running checks. Isolate power, verify de-energization and relieve any trapped pressure before service. Preserve water traces, marks and debris on the original return. Repeatedly sliding tools onto it can create new marks that make the original damage harder to distinguish.

If a repaired batch is involved, retain one checked tool and the corresponding setup drawing with the inspection record. A different supplier's sleeve can look the same in a photograph while having a different outside diameter or transition. The instruction and the tool need to match.

Inspect the exit of the installation sleeve as well as its lead-in. A burr on a protective tool can become the cutting edge the tool was intended to cover. Define tool inspection and withdrawal conditions after maintenance or a batch change. After mounting, check for a rolled lip and displaced spring using a method that does not damage the seal again. If the proposed examination requires prying the lip open, ask the designer for a suitable inspection method. Link the tool identifier, assembly direction and station to qualification samples. That record makes an occasional cut easier to trace than a generic statement that operators used a sleeve. It also helps a repair centre confirm that its replacement tool has the same geometry.

Frequently asked questions

Should I just polish the burr away?

Any rework must preserve the designed dimensions, finish and coatings. Have process engineering decide whether the shaft or the tool should change.

Why can it pass a static leak check and still leak in motion?

A small cut can behave differently under rotation, runout and temperature. Static success is not a substitute for an approved running check.

Can the removed new seal be reused for the test?

Removal can add lip or outside diameter damage. Follow the service instructions and keep evidence parts out of the replacement stock.

Related reading